Dongguan Sen 5052H32 aluminum and metal materials Co., Ltd. is a world-renowned brand agents aluminum, aluminum coil, aluminum rod and other professional Alcoa aluminum supply of imported brands are: Alcoa ALCOA, Alcan ALCAN, Aleris ALERIS Sumitomo, Nippon Light Metal, Kobe Steel KOBELCO, Korea NOVELIS, Russia KUMZ etc; the supply of domestic brands are: China Aluminum Corporation (a subsidiary of Northeast Light Alloy, SWA, Northwest Aluminum), and other well-known brands. Copper brand: the company sells: aluminum, copper, stainless steel, tool steel, sheet metal rods calandria belt material, aluminum are:... 1050.1060.1070.1100.2024.5052.6061.6063.7075 etc. ..... copper are:......... copper beryllium copper brass bronze copper-tin bronze, phosphor bronze, aluminum bronze chrome zirconium copper-nickel alloy stainless steel, tungsten copper etc ...... there. :. SUS201.SUS303.SUS304.SUS316 roll strip ... a, 5052h32 5052 aluminum for the introduction of aluminum AL-Mg alloy aluminum, is the most widely used as a rust-proof aluminum, high strength of this alloy, particularly is an anti-fatigue strength: plasticity and high corrosion resistance, heat strengthened ,, not half cold hardening during plastic is still good, when the plastic work hardening is low, good corrosion resistance, good weldability, machinability bad, can be polished. . Two, 5052h32 5052 aluminum aluminum range of applications use mainly for applications requiring high plasticity and good weldability, working in a liquid or gaseous medium low load parts, such as a mailbox, gasoline or oil conduit, liquid containers and various other deep drawing made with a small load parts: wire used to make rivets. Also commonly used in transport vehicles, vessels, sheet metal parts, instruments, lights bracket and rivets, metal products, electrical appliances, such as Shell. Three chemical composition, 5052h32 aluminum plate: Aluminum Al: margin; silicon Si: 0.25; copper Cu: 0.10; Mg Mg: 2.2 ~ 2.8; Zinc Zn: 0.10; Mn Mn: 0.10; chromium Cr: 0.15 ~ 0.35; iron Fe : 0.4 0. Four, 5052h32 aluminum mechanical properties tensile strength (σb): 170 ~ 305MPa Conditions yield strength σ0.2 (MPa) ≥65 modulus of elasticity (E): 69.3 ~ 70.7Gpa annealing temperature: 345 ℃. Fifth, the surface quality of a 5052h32 aluminum surface does not allow cracks, corrosion spots and nitrate traces. 2. Allow the surface defect site where the depth does not exceed the nominal wall thickness of 8% from the size of the skin, bubbles, surface roughness and local super mechanical damage, but can not exceed the maximum defect depth 0.5mm, the total area of ??the defect does not exceed the total area of ??the plate 5%. 3, allows the supplier to the lighting along the longitudinal profile smooth surface. 4. Other requirements: There is a demand side and the supply side drawn up. Six, 5052h32 aluminum welding electrode Model 5052 is available ER5356 aluminum welding rod after welding to meet the mechanical properties of 5052 aluminum. 5356's chemical composition: Si: 0.25; Fe: 0.40; Cu: 0.10; Mn: 0.05-0.20; Mg: 4.5-5.6; Cu: 0.02--0.20; Zn: 0.10- 0.20; Ti: 0.06--0.20; Al : margin; 5336 higher magnesium content. Seven, 5052h32 aluminum series and 1060 series aluminum difference Hardness: 1060 aluminum tensile strength of between 110-130, and 5052 series of tensile strength is reached between 210-230 hardness That 5052 than 1060 100% high hardness. Elongation: The elongation of 1060 series of 5%, while the 5052 series of extension rate of between 12-20%, also can be considered, in the 5052 series of the hard case 100% than 1060, the elongation increased by 200 about%. Chemical properties: 1060 pure aluminum, aluminum alloy 5052, 5052 under special circumstances corrosion better. Eight, the relevant product standard aluminum with national standards (GB / T 3880-2006), apply a unified standard aluminum strip material.