5052H32 aluminum Dongguan Sen and Metal Materials Co. is an agent of world-renowned brand of aluminum, aluminum coil, aluminum rod and other professional Alcoa aluminum supply of imported brands are: Alcoa ALCOA, Alcan ALCAN, Aleris ALERIS Sumitomo, Nippon Light Metal, Kobe Steel KOBELCO, South Korea NOVELIS, Russia KUMZ like; the supply of domestic brands are: Aluminum Corporation of China (under the Northeast Light Alloy, SWA, Northwest Aluminum), and other well-known brands. Copper brand: the company sells: aluminum, copper, stainless steel, tool steel, sheet metal material rod belt discharge pipe, aluminum are:... 1050.1060.1070.1100.2024.5052.6061.6063.7075 etc. ..... copper are:......... copper beryllium copper brass bronze copper-tin bronze aluminum bronze phosphor bronze copper-nickel alloy chromium zirconium copper tungsten steel and so on ...... there. :. SUS201.SUS303.SUS304.SUS316 roll strip ... a, 5052h32 5052 aluminum aluminum introduced as AL-Mg alloy aluminum, is the most widely used as a rust-proof aluminum, high strength of this alloy, particularly is a fatigue strength: high ductility and corrosion resistance, heat strengthened ,, not half cold hardening during plastic is still good, when the plastic work hardening is low, good corrosion resistance, good weldability, machinability bad, can be polished. . Two, 5052h32 scope of application of aluminum 5052 aluminum uses mainly used for high plasticity and good weldability, working in a liquid or gaseous medium low load parts, such as mailboxes, gas or oil pipe, a variety of liquid containers and other deep drawing made with a small load parts: wire used to make rivets. Also commonly used in transport vehicles, vessels, sheet metal parts, instruments, lights bracket and rivets, metal products, electrical appliances, such as Shell. Chemical composition three, 5052h32 aluminum plate: aluminum Al: margin; silicon Si: 0.25; copper Cu: 0.10; Mg Mg: 2.2 ~ 2.8; zinc Zn: 0.10; Mn Mn: 0.10; chromium Cr: 0.15 ~ 0.35; iron Fe : 0.4 0. Four, 5052h32 aluminum tensile mechanical properties (σb): 170 ~ 305MPa conditions yield strength σ0.2 (MPa) ≥65 modulus of elasticity (E): 69.3 ~ 70.7Gpa annealing temperature: 345 ℃. Fifth, the surface quality 5052h32 aluminum plate 1, the surface does not allow cracks, corrosion spots and nitrate traces. 2. Allow the surface defect site where the depth does not exceed the nominal wall thickness of the skin from size 8 percent, bubbles, surface roughness over and local mechanical damage, but can not exceed the maximum defect depth 0.5mm, defect total area does not exceed the total area of ??the plate 5%. 3, allows the supplier to the lighting along the longitudinal sections smooth surface. 4. Other requirements: the demand side and the supply side to develop their own. Six, 5052h32 aluminum welding electrode Model 5052 is available ER5356 aluminum welding rod, welding after 5052 to meet the mechanical properties of the aluminum plate. 5356 chemical composition: Si: 0.25; Fe: 0.40; Cu: 0.10; Mn: 0.05-0.20; Mg: 4.5-5.6; Cu: 0.02--0.20; Zn: 0.10- 0.20; Ti: 0.06--0.20; Al : balance; 5336 magnesium content higher. Seven, 5052h32 aluminum series and 1060 series aluminum distinction hardness: tensile strength 1060 aluminum plate between 110-130, and 5052 series of tensile strength reached a hardness that is to say between 210-230 5052 than 1060 high hardness of 100%. Elongation: 1060 series extends 5%, while the 5052 series of elongation of between 12-20%, also it can be that 100% of the 5052 series hard case than 1060, the elongation increased by 200 about%. Chemical properties: 1060 pure aluminum, aluminum alloy 5052, 5052 under special circumstances better corrosion resistance. Eight, the relevant product standard with aluminum national standard (GB / T 3880-2006), apply to the unified standard aluminum strip material.